9Before usePart name Detail by useDeclutch knob Refer to P.14[Winding the lower thread] 4)Buttonhole adjustment screw Refer to P.36 [侀 Adjustment of b
10Sewing preparationsII. Sewing preparations1. Connecting the power使使Machine with a power switch使使Turn the power switch off when inserting the power p
11Sewing preparations使使Machine without a power switch使使 RS2000 A/B series only.Hold the power plug when removing it from the outlet.Not doing so coul
12Sewing preparations2. Taking out the bobbinBefore taking out or setting the bobbin case, remove the power plug from the outlet.Not doing so could ca
13Sewing preparations3. Winding the lower threadBefore taking out or setting the bobbin case, remove the power plug from the outlet.Not doing so could
14Sewing preparations1. Move the declutch latch in the direction(in the direction of the arrow)(This ensures that the needle does not move.)2. Pass
15Sewing preparations4. Threading the lower threadBefore setting the bobbin case, remove the power plug from the outlet.Not doing so could cause an in
16Sewing preparations5. Threading the upper threadBefore threading the upper thread, remove the power plug from the outlet.Not doing so could cause an
17Sewing preparationsSupport the thread on the sewing machine with one hand, using the other hand pass the thread around the thread guide as shown in
18Sewing preparations6. Pulling up the lower threadHold the end of the thread, turn the handwheel towards yourself for one full turn, and stop when th
1Type designationRS series has several types.The types are shown on the model label as follows:MODEL/MODELE(MODEL NAME) SERIES/SERIERS SERIES/SERIE
19Sewing preparations7. Main stitch pattern uses Depending on the model of your sewing machine, some of the stitch patterns are not available. (refe
20Sewing preparations8. Application of each stitch patternTurn the handwheel towards yourself to raise the needle to the highest position.Turn the p
21Sewing preparations9. Changing the presser footBefore changing the presser foot, remove the power plug from the outlet.Not doing so could cause an i
22Sewing preparations侀Installation侀Position the presser foot pin directly below the groove in the presser foot holder.Lower the presser foot lever to
23Sewing preparations10. Changing the needleBefore changing the needle, remove the power plug from the outlet.Not doing so could cause an injury.Broke
24Sewing preparations11. Relationship between the needle, thread and fabric, and adjusting the sewing machineThe quality of the sewing finish will imp
25SewingIII. Sewing1. Straight stitching and reverse sewingReverse sewing is performed at the beginning and end of sewing to prevent the thread from u
26Sewing侀Thread cutter on the needle bar侀* The thread cutter may differ from model to model.Line up two threads and cut with the thread cutter on the
27Sewing侀Sewing thick fabric侀When sewing thick fabric from the edge, the presser foot may tilt and be unable to feed through the fabric.Place fabric o
28Sewing侀Sewing tube-shaped fabrics侀Pull out the extension table (accessory box) in the direction of the arrow.Sew tube-shaped fabrics such as trouser
2CONTENTSI. Before use ... 31. Important safety instruction
29Sewing2. Zigzag sewingThere are various types of zigzag sewing methods, such as applique and overcastting.Turn the handwheel towards yourself to ra
30Sewing3. Adjusting thread tensionBefore adjustment, check again that "P.16 [Threading the upper thread]" has been performed correctly.侀Adj
31Sewing4. OvercastingThis is a sewing method that prevents unraveling at the edge of the fabric.Is not available for 16/18 stitch model. (refer to P.
32Sewing5. Blind hem stitchingIn this sewing method the stitch cannot be seen on the right side of the fabric.Fold back the fabric so that the folded
33SewingIt is easier to sew accurately if a blind stitch foot is used. (Optional Accessory)
34Sewing6. ButtonholeButtonhole sewing to match the size of the button is possible.For stretch fabric or thin fabric, a fusible interlining on the wro
35SewingAlign the buttonhole foot division line closest to you with the guide line, and lower the presser foot to the start line of sewing on the fabr
36SewingWhen using the buttonhole cutter to cut the buttonholes, do not hold the fabric in front of the cutter.Doing so could cause an injury to your
37Sewing7. Zipper sewingBefore changing the presser foot, remove the power plug from the outlet.Not doing so could cause an injury.Change to the zippe
38SewingSew until just before the presser foot makes contact with the slider, and then stop the sewing machine.Turn the handwheel towards yourself to
3Before useI. Before use Be sure to read this section before use1. Important safety instructionsThese safety instructions are designed to pre
39Sewing8. SmockingIs not available for 16/18 stitch model. (refer to P.20 [Application of each stitch pattern])To make the gathering:Set the pattern
40Sewing9. EmbroideryA free machine embroidery pattern can be created. Trace your design on the material and centre it in an embroidery hoop. Lay stab
41SewingLoosen the presser foot holder screw with the needle plate screw driver to release the holder.Firmly stretch the fabric with the design and s
42Special specificationsIV. Special specifications1. Using the needle threaderBefore using the needle threader, remove the power plug from the outlet.
43Special specificationsHold the thread set in the hook guide to the right side and insert in the needle threader groove.While raising the needle thre
44Special specifications2. Using the presser foot pressure adjuster The presser foot pressure adjuster may differ from model to model.侀Push-down type
45Special specifications3. Using the drop feedThe feed dog can be lowered when feeding the fabric freely by hand, for example, when embroidering or qu
46MaintenanceV. Maintenance1. Feed dog and hook maintenanceIf the sewing machine makes a loud noise or rotates slowly, the oil could have run out, or
47MaintenanceOpen the left and right stoppers to the outside. (in the direction of the arrow.)Take out the shuttle hook cover.Take out the shuttle ho
48Maintenance2. Hook installationThe hook is installed by reversing the removal procedures.Replace the shuttle hook.Align the projection of the shuttl
4Before useWhen the machine is not in use it should be stored safely, not on the floor as protruding parts could cause injury if a person fell on the
49Maintenance3. Light bulb replacement Light bulb is not equipped with RS2000B series.Before changing the light bulb, remove the power plug from the
50Maintenance4. TroubleshootingWhat is the problem? Check the following possibilities before taking the sewing machine in for repair.Trouble Cause Cou
51MaintenanceIf the above treatments do not solve the problem, contact the service center as described in your warranty.5. Servicing double-insulated
52OthersVI. Others1. SpecificationsIf you have any queries about this TOYOTA sewing machine, check the warranty for details.2. RecyclingWe are committ
53Others
5Before use2. How to change the power plugThe wires in this mains lead are coloured in accordance with the following code: BLUE-NEUTRAL BROWN-LIVE (
6Before use3. Part names Some parts may not apply to your sewing machine. The MODEL and SERIES numbers are located on the model label on the back of
7Before usePart name Detail by useDeclutch knob Refer to P.14[Winding the lower thread] 4)Buttonhole adjustment screw Refer to P.36 [侀Adjustment of bu
8Before use Some parts may not apply to your sewing machine. The MODEL and SERIES numbers are located on the model label on the back of the sewing ma
Kommentare zu diesen Handbüchern